Gunite Finish Supply

Pool Plastering, Pool Tiling and Pool Coping
Located in Hudson and serving surrounding areas Contact Us
Pool Skimmer
Pool Maintenance

Deck-O-Seal

About Deck-O-Seal, Pool Products

We use Deck-O-Seal products in our coping applications. On all of our new and pool renovations. This product line is manufactured by WRMEADOW. Inc.

www.wrmeadows.com

To order Deck-O-Seal products, call us at 1-(800) 947-7807

DECK-O-SEAL ONE STEP is a tude grade product used to repair damaged Deck Seal and to complete a water tight seal to the under side of a Cantilever Decking where the decking and the tile meet.

DECK-O-SEAL (Self- Leveling Pourable) Is used for horizontal applications, and is excellent for pool coping to decking joint sealant.

SEALTIGHT KOOL-ROD is a flexible rope-like foam joint backing material. Used in Pool Coping Applications and for Cantilever Decking where there is a need for backing, it also helps to control depth of Deck-O-Seal Sealants. It does not allow air or moisture entrapment. It installs quickly and stays in place.

BELOW IS SOME BREIF PRODUCT INFO...

  • DECK-O-SEAL ONE-STEP may be applied by manual or air operated caulking guns, putty knife, or trowel. No primer is required. Joints should be cleaned and freee from dirt, dust, laitance, oil, grease, wax, curing compound, loose material, etc.
  • DECK-O-SEAL ONE-STEP, under normal conditions, (70F. and 50% relative humidity) will form a skin on the sealant in approximately 8 hours. To speed the formation of the surface skin, the sealant in the joint may be tooled with water which results in a skin forming in about a half hour. The time required for complete curing of the sealant, depends upon the size of the joint, temperature, and humidity. High temperatures and high humidity promote rapid curing. Conversely, at low temperatures and low humidity, a longer time will be required to develop the optimum qualities of the sealant.
  • AFTER APPLYING SEALANT, application equipment should be cleaned promptly with Xylene or Toluene.

PRODUCT COVERAGE

The chart shows approximate number of lineal feet which can be sealed with a 11-ounce Cartridge.

PRODUCT MAINTENANCE

Damaged sections can be removed and resealed with ONE-STEP. Joints must be cleaned if contaminated.

PRECAUTIONS

Avoid direct contact with this product. If irritation occurs and persists, seek medical attention. Consult product Material Safety Data Sheet for complete health and safety information. NOTE: Paint can not be applied over DECK-O-SEAL ONE-STEP.

TWO PART ELASTOMERIC
POLYSULFIDE-BASED JOINT SEALANT

PRODUCT DESCRIPTION

DECK-O-SEAL Two Part Elastomeric Polysulfide-Based Joint Sealant is a premium grade, pourable,self-leveling, sealant which cures at ambient temperature to a firm, flexible, tear-resistant rubber. DECK-O-SEAL is highly resilient and has excellent recovery characteristics after extended periods of compression or elongation.

DECK-O-SEAL has outstanding resistance to weather-aging and won't discolor. It provides excellent adhesion to most surfaces without using messy primers.

PRODUCT COVERAGE

The chart shows approximate number of lineal feet which can be sealed with a 96 ounce DECK-O-SEAL kit.

PRODUCT MAINTENANCE

If DECK-O-SEAL is damaged, and the joint has not been contaminated, it can be repaired by cutting out only that part and resealing it with DECK-O-SEAL. Pint size available.

SEALTIGHT? KOOL-ROD BACKER ROD

PRODUCT DESCRIPTION

SEALTIGHT KOOL-ROD is a closed-cell, polyethylene, flexible, rope-like foam joint backing material. This material is virtually non-absorbent and chemically resistant to most solvents. KOOL-ROD will not stain or adhere to sealant materials. It is fully compatible with acrylic, butyl, polyurethane, polysulfide, silicone and most other cold applied sealant compounds.

PRODUCT USE

SEALTIGHT KOOL-ROD is highly adaptable for both vertical and horizontal applications. It is commonly used in glazing operations, copings, between pre-cast panels, around door and window perimeters. It provides the perfect backing for all types of construction, expansion, isolation, control and pavement joints.

FEATURES AND BENEFITS

"Controls depth of sealant/Ensures proper joint design ratio. "Forces sealant against joint sidewalls/Provides maximum sidewall adhesion. "Sealants will not adhere to KOOL-ROD/Eliminates 3-sided joint adhesion failure. "Closed cell foam technology/Does not allow air or moisture entrapment. "Easily compressible, lightweight/Installs quickly, stays in place. "New, easy to handle, smaller packaging/Added contractor convenience.